mr.coffee 364 Posted September 25, 2009 Report Share Posted September 25, 2009 Read these directions entirely ~before~ starting, looking at the accompanying pictures. Click on the pictures for larger versions. Then read them again. Only after you are sure you understand are you to begin. Once a piece is cut, it cannot be uncut. Once a piece is glued, it cannot be unglued. Make sure your parts are lined up correctly before gluing! In fact, you may want to assemble the whole thing without glue at first to make sure it all fits right. Good luck! Due to board constraints, this will be broken up into several posts. The directions are also viewable at: http://www.csno.biz/puppy/DIY-Agility/Hurd...structions.html Tools you will need: Measuring tape and/or ruler Saw - I used a Marples Japanese pull saw, a hacksaw would work File - I used a single-cut/double-cut metal file that happened to be in my toolbox Sanding sponge - again, already in my toolbox, mine has coarse and fine sides Glue - there are various cements for PVC pipe, I used Oatey medium/orange CPVC Cement A miter box may help you make your cuts square, I didn't bother Materials you will need: 3/4" PVC pipe - I bought mine in 10' lengths 3/4" Tees - you will need 4 for the base, and 2 for each bar on your hurdle 3/4" caps X 6 - more or less optional ...to be continued... Quote Link to post Share on other sites
mr.coffee 364 Posted September 25, 2009 Author Report Share Posted September 25, 2009 Start by cutting your PVC into the required lengths. With each cut, I used the file and sanding sponge to clean up the edges and smooth them, inside and out. I chose to make my hurdle 36" wide, based on the assumption that that's ample width for a small dog like a Shih Tzu. I believe most regulation Agility hurdles are 5' wide, likely to accommodate larger dogs. You will need one cross bar for the base, then one for each additional bar on the hurdle. That means I cut three lengths of 36". For the legs, I cut four lengths of 18" each. For close joints, I cut short pieces 1-3/8" long. To provide for 4" intervals on my bars, I cut pieces 2-7/8" long. This length may vary depending on the exact specifications of your Tees. Now we'll assemble the base. Glue a cap onto one end of each of the 18" legs. Glue the other ends into Tees so that you have two sets of legs with Tees in the middle. Using the 1-3/8" pieces, connect a second Tee to the sides, making sure that the side of the second Tee is vertical. I used a carpenter's square to check this, you can use anything fairly square. Add a 1-3/8" piece to the vertical side of the second square. You should now have something that resembles this: To build the supports, you'll need to cut the Tees so that your bars are easily knocked off. Cut from one end of the Tee into the side, then cut into the side toward the main body of the Tee. Again, clean up the cuts with the file and sanding sponge. You should wind up with something that looks like this: You need two supports for each bar. ...to be continued... Quote Link to post Share on other sites
mr.coffee 364 Posted September 25, 2009 Author Report Share Posted September 25, 2009 Now we're ready to assemble the supports. I stopped at 8", although I haven't glued the tops on so I can increase to 12" whenever we're ready. For each side you'll need a support, a 2-7/8" piece, another support, a 1-3/8" piece, and a cap. Assembled, the supports should look like this: Connect the supports to the base sections: Use a 36" piece to connect the two sides of the base. Now you can rest the bars across the supports, and it should look like this: If it all looks right, fits right and you are satisfied with the heights of your bars, etc., you may begin gluing it all together, or at least as much as you want. I found that I can glue the legs and the supports, then the whole thing will tear down nicely to store in a duffel bag. -m Quote Link to post Share on other sites
mr.coffee 364 Posted September 25, 2009 Author Report Share Posted September 25, 2009 BTW, the weave poles instructions will be next, but I won't make any promises as to ~when~ exactly. Tentatively, look for them over the weekend. Enjoy!!! It's not hard, I promise! -m Quote Link to post Share on other sites
tzuhouse 4 Posted October 14, 2009 Report Share Posted October 14, 2009 Mike, thank you SO much for posting this with such great pics and instructions. When we have some time, I am gonna get the hubby on this cause I would love to train Maddy to do the weave and the jump...Josie too, but I somehow think Maddy would do it best, but I may be wrong. Can't wait for the other instructions too....thanks again. Sorry so late for my thanks.. Quote Link to post Share on other sites
mr.coffee 364 Posted October 16, 2009 Author Report Share Posted October 16, 2009 D'OH!!!! Did I space the weave pole how-to? Drat....things have been non-stop chaos lately. Anyway, yeah, let me know how it works out! We haven't done as much jumping and weaving lately, just treks to the levee and running laps in the yard; but it's cooling off finally so we might be getting more motivated now. -m Quote Link to post Share on other sites
MaryBebo 3 Posted October 16, 2009 Report Share Posted October 16, 2009 :flowers: :D Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.